Poulan Chainsaw 2150

jsouth3(9)January 30, 2010

Got this chainsaw running,will not oil the chain.Found the little spring missing,inside the oil tank.How do you replace the oil dip tube.I took the clutch off and the oil pump.Does it push through the tank or pull out from the outside.

Thanks,

Jerry

Thank you for reporting this comment. Undo
glenam

Jerry,
I think the little spring you are missing in the tank is the filter.
Here's what I would try to make sure the oiler is working.
Fill oil tank 1/4 full with fuel mix. Let sit for a few minutes. Shake, flush and dump.
Lightly blow compressed air through the pickup tube from the outside of the case. We're just trying to ensure the tube on the inside of the oil tank is not obstructed.
Re-assemble oil pump and it's cover. Fill 1/2 oil tank with light engine oil, e.g. 10w-30.
Start engine w/o bar and chain. See if oil comes out to bar area.
If it doesn't, I'm suspecting the worm gear is wore out.

You got an IPL for this saw?
You use sealant to re-assemble engine ??
Let us know,
Thanks,
Glen

    Bookmark   January 31, 2010 at 9:25AM
Thank you for reporting this comment. Undo
jsouth3(9)

gleman,is the worm gear the little plastic gear that on the oil pump,that rotates on the spring,that on the crankshaft.If so it looks a little chewed up.I will do what you said about cleaning the tip tube.Yes I have the IPL for this saw.I took the saw apart and put it back together.I did not have any sealant,so I made a gasket for the crankshaft cover.It will run but won't idle.I think I have a air leak due to the gasket, I made for the crankshaft cover.I will take the saw apart again and use some sealer.I will be a few days.I will let you know how it comes out.

thanks,
Jerry

    Bookmark   January 31, 2010 at 6:11PM
Thank you for reporting this comment. Undo
glenam

The oil kit part no. I see is 530-071259.
You can get it from Outdoordistributors for $6.48 or,
from Poulan for 8.88.
I'm surprised it would even start with a paper gasket.
Let us know how it turns out,
thanks,
g

    Bookmark   February 1, 2010 at 8:10AM
Thank you for reporting this comment. Undo
jsouth3(9)

Thanks,for the part#.I will let you know how it comes out.I have to wait till the weather clears up.I have to work on it outside in my driveway.

Jerry

    Bookmark   February 1, 2010 at 3:24PM
Thank you for reporting this comment. Undo
jsouth3(9)

Update,seal the crankshaft cover with sealant,and the chainsaw runs great.Had to replace the oil pump so the chain oiler works fine,Thanks for all the help.

Jerry

    Bookmark   February 10, 2010 at 4:33PM
Sign Up to comment
More Discussions
General craftsman tiller gearbox question.
Ages ago in the early 90's, I bought a Craftsman 5hp...
bliackbeard
What’s a good safe cure to stop or slow root entering sewer line?
What’s a good safe cure to stop or slow root entering...
loger_gw
Woodzig electric pruner
I have a Woodzig electric pruner and use it often....
ranger_ric
Who Makes This 'New' Craftsman 50cc Chain Saw?
Doing a little research on possible replacement saws......
pgtr
MTD 8HP SnowBlower
I have an MTD 8hp SnowBlower Mod # 317E640F352. The...
Jeffery Smith
Sponsored Products
Trump Home Regency Burnt Bronze One-Light Wall Sconce
$178.00 | Bellacor
Blue Max 2-in-1 14/20-inch Combination Chainsaw in Protective Case
Overstock.com
Ambiance Bisque Pecos Bathroom Wall Sconce
$129.60 | Bellacor
DECOLAV Cabinets Gavin 30 in. W x 21.50 in. D x 35.25 in. H Birch Vanity
Home Depot
GreenWorks Li-Ion 16-inch Cordless Chainsaw with Battery and Charger
Overstock.com
Nik One Floor Lamp
ModernistLighting.com
Bocci | 21.50 Fifty Pendant Chandelier
YLighting
Chainsaw Throw Pillow
$34.99 | zulily
© 2015 Houzz Inc. Houzz® The new way to design your home™