Manual for McCullough MAC 2816

gdankoJanuary 22, 2007

Hi all, I inherited a MAC 2816 from a friend and I would like to strip it apart to clean it. However, I cannot figure out how to get the trimming head off. I have an older Eager Beaver model which has tabs on either side of the trimmer head. When I press these tabs the top comes off so I can add new line. However, on the MAC 2816 there are no such tabs so I do not even know how to change the line!

Any MAC 2816 owners want to help me out?

Thanks!

Gary

Thank you for reporting this comment. Undo
fergus7(NS)

Hi I had one of these they have a real problem with the coils, to take my trimmer head off you just unscrew the bump knob it is left hand thread I think then the whole head will come off. you may have to pry the center section out this is the spool for the line nothing holds it in there is just a spring in back of it. I have an owners manual if you need one I can copy it and send it to you.
regards
rod s

    Bookmark   January 23, 2007 at 9:50AM
Thank you for reporting this comment. Undo
gun25vc_hotmail_com

I have manual and partlist for mac2816 as pdf.
Need an address to send to, about 6 MB and 600 KB

    Bookmark   February 5, 2007 at 5:59PM
Thank you for reporting this comment. Undo
dknanie

I have trouble to start mine as well, and I also need to open up and clean it. Can you please also send me the manual? I really appreciate it. My email is "dknanie@yahoo.com.

    Bookmark   September 23, 2008 at 8:17PM
Thank you for reporting this comment. Undo
itsmejuliana

I, too, need the manual for the MAC 2816. Please send it to itsmejuliana@gmail.com.
Thank you so much!

    Bookmark   May 15, 2009 at 5:42PM
Thank you for reporting this comment. Undo
stuartraymond141_hotmail_com

Hi, please email me a copy of the manual for the MAC 2816 as well at stuartraymond141@hotmail.com

Thanks!

    Bookmark   May 19, 2009 at 11:11PM
Thank you for reporting this comment. Undo
tomdormer

Hi, please email me a copy of the manual for the MAC 2816 as well at tadormer@mtmail.biz
Thanks!

    Bookmark   May 21, 2010 at 6:36AM
Thank you for reporting this comment. Undo
crumleyhorseshoeing_yahoo_com

hi. could you email a copy of the manual for the 2816 trimmer. thanks alot.

    Bookmark   May 29, 2011 at 5:12PM
Thank you for reporting this comment. Undo
countrycareexpress_yahoo_com

Could you send me a copy of the manual for the 2816 trimmer.
Thank you very mch.

    Bookmark   June 1, 2011 at 8:48PM
Thank you for reporting this comment. Undo
kirsten658_gmail_com

Hi - Could you e-mail me a copy of the Mac 2816 manuel also please?

Thanks!

--Kirsten

    Bookmark   June 18, 2011 at 8:01PM
Thank you for reporting this comment. Undo
bowen4201_yahoo_com

I would love a copy of the manual for this weekwacker too. Thanks alot,
Judy

    Bookmark   June 24, 2011 at 11:33AM
Thank you for reporting this comment. Undo
knhall09_gmail_com

If possible I would also like a copy of the manual for the MAC 2816!!!

Thanks!!!

    Bookmark   June 27, 2011 at 10:26AM
Thank you for reporting this comment. Undo
lightning2003sb

Please email a copy of the manual for the Mac 2816. Thanks!

lightning2003sb@gmail.com

    Bookmark   April 27, 2012 at 9:51PM
Sign Up to comment
More Discussions
troy bilt horse question
Went to check the transmission fluid today and noticed...
snuffyinatl
Reciprocating Saw
I am looking to buy a reciprocating saw. I am not looking...
pirate94
Sears air compressor engine won't run when plugged in
Sears Paint Sprayer/Air Compressor Model No. 106.153542...
Cletus77
Predator 212cc Engine, Harbor Freight FYI
Hi Folks, Been thinking of getting one of these for...
exmar
Troy Bilt Horse Drive Shaft Bearings
I took my horse apart because the front transmission...
gildomilo
People viewed this after searching for:
© 2015 Houzz Inc. Houzz® The new way to design your home™