Utility Trailer Sides

monroe(2)August 3, 2006

Wanting to construct wooden sides for a 6 x 12 flat deck trailer. Trailer has stake pockets to accomodate 2 x 4. Using this for construction debris, mulch, trips to dump. Of those that have constructed similar siding, what spec of lumber have you use and found works or (perhaps) did not? Was considering 2x4 verticals with 2 x 6 or 2 x 10 horizontals, but perhaps the 2x horizontals are overkill? I've had some suggest lighter weight 1 x 6. thanks

Thank you for reporting this comment. Undo
tkendr01

Use 2x4 verticals into the stake pockets. Get two sheets of interior plywood 3/8" or 1/2" thickness. Rip both sheets to 24x96; cut one in half to 24x48. Screw the plywood panels to the uprights and scab on 2x4 blocks at the corners and bridging the 2 sections (8'+4') on the sides. Cut one section down to 6' for the front.
You will find that branches cannot stick through the plywood and make it difficult to unload.
Before you load the trailer, lay a length of chain in the bottom of the trailer. If you can tie it off, the trailer can be unloaded quickly by just driving the trailer out from under the load. Then pull the chain out one side and take it with you.
I have done whis to raise the bed height of my pickup by extending the walls above the sides with plywood. When I am done hauling, I unscrew the plywood from the 2x4's. My 2x4's are whitewood rather than pine to save weight.

    Bookmark   August 4, 2006 at 12:15AM
Thank you for reporting this comment. Undo
earthworm(6 Pennsylvania)

In this situation I would use nothing but pressure treated wood, and from a better lumber store.
The big box stores seem to sell a lot of junk wood.

    Bookmark   August 5, 2006 at 12:37PM
Thank you for reporting this comment. Undo
montesa_vr(Minnesota)

I've had good results with 1/2" pressure treated plywood treated with an opaque stain designed to use on green-treat wood.

My experience with the Menards big box stores here in Minnesota is that their lumber quality varies from unusably poor to the best you can find anywhere. If you are able to go early in the day, and especially on weekdays, you can sort through a pile and pick out good lumber at a discount price. I wouldn't trust them to deliver wood I hadn't personally inspected.

    Bookmark   August 7, 2006 at 4:10PM
Thank you for reporting this comment. Undo
mike_in_kc(4)

I've framed out sides for two trailers over the years. Mine had angle iron rails about 8" above the floor. My solution there was to make 32" sidewalls out of 3/4" exterior plywood (can't figure out why an earlier replier would use interior ply!) and frame the perimeter with pressure treated 2x4's. space vertical 2x4's about every 3' and toenail all joints with exterior deck screws. As far as attaching the walls to the trailer, you could use your stake pockets by running the vertical supports long enough to utilize them. In my case, I bought J bolts and washers through the bottom framing & plywood to hook onto the angle iron rails. With this connection, I can remove the walls in 5 minutes when I need to. To keep the walls in line, I screwed cleats to the floor inside the walls. To hold the front corners together, you could use L brackets, but I ordered corner braces for trailers from Northern Tools. They're interlocking and secure tightly, but unhook easily with an upward lift on the sidewalls. Hope this helps!

    Bookmark   August 8, 2006 at 1:03PM
Sign Up to comment
More Discussions
Testing the new format X allowing multiple attachments.
I am back to two Lexan chain guides due to a chain...
loger_gw
Kohler K181 valve clearance
The engine would run perfect for maybe 30-45 minutes,...
snuffyinatl
2-cycle engine troubleshooting
My 2-cycle blower cannot be started. There is a hot...
slim50
troy bilt horse question
Went to check the transmission fluid today and noticed...
snuffyinatl
Best gas leaf blower?
Can anyone recommend a good gas powered leaf blower?...
robar
People viewed this after searching for:
© 2015 Houzz Inc. Houzz® The new way to design your home™