Getting chain back on Husqvarna E235 Chainsaw

cbentsenSeptember 8, 2011

I'm a very occassional chainsaw user - mostly use my Husqvarna for cutting up downed trees and such. The chain has come off of the blade, and for the life of me, I can't get it back on. I've loosened the chainsaw blade tightening adjustment dial to the loosest setting, and have tried to get the chain back on similar to how you get a chain back on to a bicycle gear - but no luck - it is still too tight to get the chain back into the groove on the blade. Is there a trick to doing this manouever on this particular model of chainsaw? I'd hate to have to bring it to a dealer just to do this.

Thank you for reporting this comment. Undo
fisher40037

You will either have to get a new chain, or grind the burrs
off of the bottom of your chain.
No decent shop will offer to "doctor" the chain to be used.

Fish

    Bookmark   September 8, 2011 at 8:12PM
Thank you for reporting this comment. Undo
rcmoser

Most of the time that's not enough to get it back on the clutch teeth (not familar with that saw but most are the same??). You will probably have to take the nuts off that hole the bar cover and bar on. swing the bar out and thread the chain on the clutch teeth first then straighten the bar while guiding the teeth into the bar groove.

Ok, I guessing you clean the saw, check tension, and sharpen the teeth on the chain after every use??? IMO the saw will be ready when you need it. Most of us for every tank full of gas the chain is hit three or four strokes with the file and the tension is reset on the chain. After use the saw bar is removed the clutch and oiling area cleaned up, the bar grooves cleaned out, the chain washed, put back togather, again hit the teeth couple times with the file and set tension. Now the saw is ready for the next episode providing you drained the oil and fuel out of it so it don't set around leaking and plugging up???

    Bookmark   September 8, 2011 at 9:38PM
Thank you for reporting this comment. Undo
cbentsen

Thanks for the advice (rcmoser). I got the chain back on and running. The trick was making sure the area around the clutch gear was clean and free of guck. After cleaning this area out, I found that I could get another eighth of an inch of slack or so by adjusting the tension knob and making sure the chain bar had moved as far as it was going to go. Then getting the chain on was a piece of cake. Now on to learning how to keep my chain(s) nice and sharp. Thanks again.

Carl

    Bookmark   September 13, 2011 at 8:58AM
Sign Up to comment
More Discussions
cultivator or tiller or both
In the past I've manually tilled and cultivated my...
Bushwhacker Blood
Any owners of the Troy-bilt Cultivator Plus?
I bought this around 1984 and have never seen another...
baymee
Are you finding Insert Pic Attachments to work as printed on this Site
Are you finding Insert Pic Attachments to work as printed...
loger_gw
Stihl Chainsaw - starts but won't run
My trusty (10 yr) old Stihl 16" chainsaw is starting...
uberfusion
Temperature alarm app for Android?
I am wondering if anyone knows of an Android app that...
armbarangel
Sponsored Products
Authentic Pestemal Fouta Charcoal Black Turkish Cotton Bath/ Beach Towel
Overstock.com
12'x18' Oversize 100 Percent Wool Sultanabad Oriental Rug Hand Knotted Sh20346
1800 Get A Rug
Natural Burnt Kiawah Roman Shade (51.5 in. x 72 in.)
Overstock.com
AHB Lancaster Counter Height Stool - 124707GS-L32
$199.95 | Hayneedle
Galetta Lush Collection Dreamax Memory Foam Pillow - IDF-DM-662
$314.94 | Hayneedle
Fair and Square Ottoman
$159.99 | Dot & Bo
Saskatoon Counter Stool
| Dot & Bo
Hopson Sectional - Key Largo Graphite Brown
Joybird Furniture
People viewed this after searching for:
© 2015 Houzz Inc. Houzz® The new way to design your home™