snow blower repair

whip62December 19, 2008

I have a snapper 2 stage snow blower model 4220. It starts and runs fine !! When ever, you go to engage the auger, it is slow to engage and when you go to blow snow the auger stops !! What is causing this and how do you repair it ??

Thank you for reporting this comment. Undo
canguy(British Columbia)

Are the shear pins in the auger broken? If not, remove the belt cover and check the forward belt, it may be excessively worn.

    Bookmark   December 19, 2008 at 8:39PM
Thank you for reporting this comment. Undo
kyler56

Hi,
Quick question about a 26 inch 8.5 horse Murray snowblower I own. The auger throws snow great and starts right up. However, when I put in gear and hold the clutch in it doesn't seem to want to go..Now, when I lift up to see if wheels are spinning they are, meaning the clutch is working...i'm stumped..any suggestions would ge great..thanks.

Kyle

    Bookmark   December 19, 2008 at 9:04PM
Thank you for reporting this comment. Undo
tomplum

My guess is the friction disc is worn. Other likely causes would be worn traction belt, detached spring or control adjustment.

    Bookmark   December 20, 2008 at 8:27PM
Thank you for reporting this comment. Undo
johnsonra2

My Snapper snow blower has been running fine this winter until the last time I tried starting it. Now, it starts and runs for about 10 seconds and then dies. I have taking the cover to the carberator off and checked to see if it was getting fuel from the tank and it is. I took the cover to the float off and inspected that and it seems fine. It seems like the fuel is just not getting to the engine. Is there a fuel filter I should be looking for?

Any suggestions?

    Bookmark   February 27, 2009 at 8:42AM
Thank you for reporting this comment. Undo
eric_rieker_yahoo_com

I have a snapper 522. The drive does not work or the gear shift and wheel are locked up. What would be the problem.

    Bookmark   January 2, 2011 at 7:05PM
Thank you for reporting this comment. Undo
baymee(LehighValleyPA)

Remove the fuel from the gas tank, stand the unit UP, remove the bottom cover under the trans, and you'll see what's going on.

    Bookmark   January 3, 2011 at 7:24AM
Sign Up to comment
More Discussions
What locked my Neighbor’s 6.5 Briggs Quantum Edge Engine?
I wanted to see what locked my Neighbor’s 6.5 Briggs...
loger_gw
Deep Spader
Has anyone used a deep spader? How did you like it?...
svachon
General craftsman tiller gearbox question.
Ages ago in the early 90's, I bought a Craftsman 5hp...
bliackbeard
Any owners of the Troy-bilt Cultivator Plus?
I bought this around 1984 and have never seen another...
baymee
New Ryobi S430 engine dies on full throttle
Just bought a new Ryobi straight shaft 4 Cycle S430...
losrubios
Sponsored Products
Nostalgia Electrics RSM-602 Retro Series Snow Cone Maker - 082677236029
$39.99 | Hayneedle
Snow White and the Seven Dwarfs FilmCells™ Framed Wall Art
$59.99 | zulily
Trident Graphite 54-Inch Ceiling Fan
$299.00 | Bellacor
Minx E94706 Multi-Light Pendant by ET2 Lighting
$420.00 | Lumens
9 3/4 Inch Outdoor Pocket Light -Black
$37.81 | Bellacor
Bruck | Vibe Down Pendant Light
$270.00 | YLighting
Del Mar Left-Facing Curved Outdoor Sofa Cover
$89.50 | FRONTGATE
Westinghouse Lighting Hardware Two 6 in. Nipples 7060600
$3.06 | Home Depot
People viewed this after searching for:
© 2015 Houzz Inc. Houzz® The new way to design your home™