Return to the Landscape Design Forum | Post a Follow-Up

 o
Question re laying brick/paver walkway on slope

Posted by marjoriest (My Page) on
Tue, May 4, 10 at 10:29

I hope someone can point me in the right direction on this project! My husband and I have a 30 ft walkway from our drive way to our front steps. He recently had the old broken concrete pulled up when we had grading work done on our gravel drive. Now we are trying to figure out how to lay a brick or paver walkway in its stead. The problem is that it is not exactly level. In fact there is a drop of approximately 14-16 inches from drive to stairs spread over the 30 foot length. We have done a fair amount of research on how to lay a walkway, but most suggest laying the base material and leveling the area. This is NOT possible. Do we just lay the brick as one would normally, aware that there is a slope? Also, due to the slope (we are on a slight hill) we do get a lot of drainage down that walk/hill. Should we just go with concrete and abandon the idea of brick?


Follow-Up Postings:

 o
RE: Question re laying brick/paver walkway on slope

Can you level it out in two or more sections, with a step up between sections?

Is it straight or curved?


 o
RE: Question re laying brick/paver walkway on slope

What zone are you in? Are ice and snow a concern?


If you're not sure which zone you're in, you can enter your zip code here:
http://www.garden.org/zipzone/index.php


 o
RE: Question re laying brick/paver walkway on slope

Marjorie,

Your existing slope would be 4.4%. A step of 7"-9" or two steps of 5" would be good and get your paver slope to around 2%. A comfortable slope to walk on and drain well. Install small lights into the steps risers to give a nice warm accent at night and make the steps less of a hazard as well. JMHO. Aloha


 o
RE: Question re laying brick/paver walkway on slope

If you're not comfortable with your skill level to build a step or two, you could always use one of the slab steps that the paver mfrs are making now. All you have to do is prep a level base and drop it in, then run your pavers up to it.

Here is a link that might be useful: Techo-Bloc Rocka


 o
RE: Question re laying brick/paver walkway on slope

Obviously, the questions above need to be answered in order to hear from people who do know what they're talking about, and I don't... really, because I've never laid brick on a slope. However, I have seen sloping installations in public places, and believe that the key to success is to lay the brick within firm boundaries. Gravity happens, and something bigger and heavier than the bricks has to be there to prevent them from sliding downhill. In public spaces, I've seen buildings serve this purpose, or street curbs.

Your climate will affect a lot of decisions in the installation, but I think gravity is global :-)

KarinL


 o
RE: Question re laying brick/paver walkway on slope

I'm facing a similar issue myself, with a sloping pathway that needs to be paved - me and DH are debating steps vs slope, and since I'm the one dragging the wheelbarrow around, I'm in favour of slope. Do you need access for anything with wheels? If not, steps might be good for your situation.


 o
RE: Question re laying brick/paver walkway on slope

  • Posted by laag z6CapeCod (My Page) on
    Fri, May 7, 10 at 7:33

No walk should ever be "level". Layout where you want the walk. They should substitute the word "flat" for "level".

This is very simple. Don't over think it(sometimes reading too much is not a good thing). Put away the bubble machine (the level).

Finish grade the area between the steps and the driveway (the whole area without regard for the walk). Then excavate (dig) out for the base material that goes under your walk. Build up that base so that it is the thickness of the brick (most concrete pavers are abut 2-3/8" thick) lower than the adjacent grade. Use a board to "screed" (smooth the surface evenly) the surface to make it even (sloped, but not up and down). Then set your bricks.

If there is a cross slope (right to left as you walk) on the adjacent grade, you should make sure that your walk has a slight cross slope in that same direction (you can use the bubble machine for checking the cross slope).

If it is pretty lever from left to right, you may consider adding a slight amount of sand down the middle of the walk to add a slight crown to the walk. This helps the walk not become sagged in the middle over time and looks nicer (in my opinion) than a flat walk. Prepare the base just as you would to do it flat.


 o
Majestic Interlock Paving

Slopes can be tricky areas to lay brick, but with the right help, you can get it done and have it look great. The slope you are describing will more than likely need steps as opposed to a smooth path. A paving consultant could help you discern how high/deep the steps needed to be and you could go from there.


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Landscape Design Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here