|
| I have the above mentioned mower with a 22" deck on it and I cannot get it to stay running. I purchased it from the woman we bought the house from, and she included the instruction manual and everything, I just don't know WHEN she purchased it. But judging by the looks of it, it seemd like a relatively newer mower(maybe three years old at that)
I put fresh gas in it, changed the oil, spark plug, and air filter and the only way I can get it to fire at all is if I take the Air filter off and pour gas directly into the carb. Even then it will only fire for a second or two before shutting down. The only way to keep it running is to push the primer while it is going. So my thought is that the fuel line might be clogged. I did not run my engine dry last year because I thought I was going to get one more cut in before the winter hit, so I'm told that stale gas could be the problem. However, I have a firend who has the same mower and he did not run his dry last year either and the damn thing started right up this year. I'd rather not have to take this anywhere to get it fixed becasue I'm really short on cash right now. Can anyone help? |
Follow-Up Postings:
|
- Posted by bill_kapaun Z8 Orygun (My Page) on Tue, May 6, 08 at 14:36
| What engine? Brand, Model, Type? |
|
- Posted by timmyG(x98larsen@yahoo.com) onFri, May 16, 08 at 11:13
| I have the same mower with the exact same problem. It has a Tecumseh: Engine Family: 3TPXS. 1951BC 195cc Model: LEV120 Spec: 362003A Warr: D Dom: 02322 |
|
| Carb is probably plugged up. |
|
- Posted by bill_kapaun Z8 Orygun (My Page) on Fri, May 16, 08 at 14:17
| That's a Tecumseh engine. IF the carb has a metal bowl, the brass nut holding it on is the MAIN JET. Clamp off the fuel line, remove the jet and clean the holes out with a fine wire, like the wire tie from a loaf of bread. IF it's a plastic bowl carb, get a new bowl kit. <$20. You might also want to drain the old fuel and dump it in the car. |
|
| I had the same problem, of course it started right after the warrantee expired. I went to a lot of forums to see what I could find. Followed all the suggestions. The first one that worked was changing the spark plug, only temporarily. I was ready to pitch the dang thing. My last ditch effort was added a healthy slug of gumout to the tank. The only time I have had a problem since was when I didn't add it. So now every time I put in gas, I add a dash of the gum out. The only thing I can think of is the fricking ethanol in the gas now. I hope it works for you. |
|
| Bill Kapaun's answer is the right one, but if you just tilt the mower up on its wheels so the carb is high and dry, you don't have to clamp the fuel line. The trouble-maker hole in the jet is the tiny one on an angle at the top of the threads (if so equipped - there are several designs of the bolt). After using the wire tie (stripped of paper, of course), blast with carb spray and rod it again with the wire. If you use Marine Sta-Bil for Ethanol fuels every time you fill your gas can, you can do away with most problems you're likely to encounter in the fuel system of the mower. |
|
| Here's an example:
|
|
- Posted by cometolowell (My Page) on Sat, May 1, 10 at 11:10
| Zen and the art of lawn mower maintenance! Thanks guys, you saved me a lot of heartache. A guy I called said "2 weeks before I can get to it" In round about fashion, I ended up tuning up the mower myself (try this try that), new filter, spark plug and oil change, scrape down the blade area. Nothing! Then I ran through your procedure and presto, 1 pull and runs great! Thanks to Bill, saxman and baymee (never would have figured out where the hole was without the photo cause of the clog). God bless you guys for taking the time! |
Here is a link that might be useful: ComeToLowell
|
| I found that the primer bulb does not work very well as it ages on TEC engines. Prime the mower at least 10 times and it will start. Don't worry abought flooding the carb. Should start 100% of the time. |
|
- Posted by truedharma108 (My Page) on Tue, May 25, 10 at 14:29
| The rubber gasket on the bulb broke off. Does it need to be replaced? Where can I obtain one? Also the gas tank is dirty & I suppose the lines, too. Is it necessary to clean them? How? On another note, I live near where your Lowell Jack Kerouac lived his last days and died. Do you want photos of his house and the hospital he died in? I have attached one of my irrelevant web sites. |
Here is a link that might be useful: Frank's Korean Buddhist Site
|
- Posted by wingslikeagales (My Page) on Sat, May 29, 10 at 20:41
| bill_kapaun's explanation was perfect as is bayman's picture. Saxman1's suggestion to jack up in mower in the front was also helpful. You can also go to the Toro website and get the part's catalog. You will need your model and serial # which are which is under the grass catcher hinged door. The official name of the nut is a High speed bowl nut which is at the bottom of the 'Float bowl'. |
Here is a link that might be useful: Toro's web site
|
| Thanks, but that's not what I meant. You raise the side of the mower with the carb and let it stand on the other side's wheels - like pouring out the oil for a change. Raising the front of the mower might help a little but is not really the trick. |
|
- Posted by Gary B(gary.behnke@yahoo.com) onWed, Mar 16, 11 at 18:20
| My mower has been idle for about 2 months and wouldn't start but the 10 pushes of the primer bulb did the trick for me. |
|
- Posted by roland(srsilva62@hotmail.com) onSat, Mar 19, 11 at 17:10
| I'm having the same issue. I just picked one up from a gentleman who hadn't used it in over a year due to being in bad health. I changed out the plug, clean gas, oil, sprayed out the carb and cleaned out the main jet. Still only able to get it to run for a few seconds from the priming. Any other ideas? |
|
| Fuel injector cleaner (concentrated) 2 ounces within fresh fuel ...should clean it out within 30 minutes . |
|
- Posted by Rich from Jersey Shore(richthebartender@yahoo.com) onSun, May 1, 11 at 13:14
| I had the same problem for the past two years. Was ready to throw away the mower. Out of desperation I found this information on this web site. I cleaned out the two holes on the brass valve, and sprayed the entire area with brake cleaner. Happy to say the mower no longer stalls out every 30 seconds. Thanks!!! |
|
- Posted by j cleveland(joffreycleveland@bellsouth.net) onTue, May 3, 11 at 21:30
| Worked like a charm!!!!!! Very good info. |
|
- Posted by AJ(triplechip03@yahoo.com) onTue, Jun 7, 11 at 12:27
| Thank You! I have a 6.75 GTS model that has always ran like a charm with normal care. I've used the mower four or five times this season and suddenlly last week it would run (lower idle than normal) and then stall. I knew it had to be a fuel issue so I cleaned everything that supplied fuel...except the main jet! Duh...As someone who regularly used to break down their 2-stroke dirtbike after so many hours, I felt kind of stupid. I cleaned the jet with the wire, hit it with some carb cleaner, and she fired right up, and stayed started. Priming the bulb the extra number of times seemed to help too. Saved me some dough, thanks again. |
Please Note: Only registered members are able to post messages to this forum. If you are a member, please log in. If you aren't yet a member, join now!
Return to the Lawn Mowers Forum
Instructions
- You must be a registered member and logged in to post messages on our forums.
- Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review the contents and make changes.
- After posting your message, you may need to refresh the forum page in order to see it.
- It is illegal to post copyrighted material without the owner's consent.
- HTML codes are allowed in the message field only.
- No advertising is allowed in any of the forums.
- If you would like to practice posting or uploading photos, please visit our Test forum.
- If you need assistance, please Contact Us and we will be happy to help.