|
| Coming from a person who used Trimmer and McLane type reel mowers all my life...going to a Rotary is really hard because I miss the way the reel mowers worked. From being able to empty the catcher while leaving the mower on to the ease of cleaning and maintaining it. Not to mention being able to see when the catcher is full and its easy emptying. No shaking, kicking, or punching....just tip and let it slide out.
I was looking at my McLane the other day. (OK...it is not a McLane but looks like one. It is a Garden Way/Troy Built that looks like McLane. Back in the day McLane let Troy Built make some reel mowers using their design. But they used higher end parts and better machining. Mostly thicker gauge steel on the parts. Even the chains are better and thicker. No wonder it still works like a champ!!!!) However I currently can't use it because it cuts the stupid Kentucky bluegrass too low. But if I can get it to 2 3/4 inches on the cutting height, I will be able to get that nice scissor cut on my lawn. In looking at it underneath, I think I might be able to mod it to where I can raise it up. I know McLane has 17 inch models for this but I like my well made 20 inch model with Grade "A" US Steel. Anyone else attempt this? I know I am not the only one to want to try this. I just lost a battle with a Husqavarna and I have a McLane Rotary that does a fine job. But lets face it...I'll have to replace it in 5-6 years. I'll have the reel mower well past that if I can use it. |
Follow-Up Postings:
|
- Posted by ggoyeneche New Jersey (My Page) on Sat, May 29, 10 at 11:01
| I was a Trimmer, Tru-Cut, and McLane guy from the early 60's until I moved to Jersey in 2000. Trimmer and Tru-cut were the "Cadillac" or reel mowers, and McLane was good low cost interpretation, especially for homeowner use. Couple comments: 1) With a rotary, if you get one with a BBC, you and remove and empty bag without shutting off engine. Deere, Honda, Toro and several others offer as extra cost option. Snapper used to, using Comet's BBC, but I don't think they offer any longer. 2) As for visually seeing bag or basket fill up, the fundamental design of a rotary inhibits that. If your McLane rotary is old enough, it has a pivoting flag and paddle to indicate how full the catcher is. Doesn't work real well, but it's OK. Snapper used to have something similar on the old (obsolete) Pac-N-Sac. Worked but not great. I currently use a commerical Snapper and prefer the soft "Z-fold" bag. I can tap with my hand and know how full it is. 3) As for your Troy-Bilt, I disagree. It was built private label for Troy-Bilt. McLane did this for literally dozens of labels: Sears, Montgomery-Wards, John Deere and others come to mind. They private labeled the 800 series edger even more extensively. The 20" (and 25") have always been better constructed than the 17" and use a superior design. I have always considered the 17" (whether self-prop, push, or manual) to be little more than junk. The 20" however, I consider an excellent, lower cost substitute for the Trimmer and Tru-Cut. If you are only mowing your own lawn a couple of time a week, the McLane will perform well if you maintain it. Heavier use, go to Trimmer Original or Tru-Cut Commerical or Professional. 4) Lastly, although you can raise the cutting height, I think you are going to be disappointed with the cut. Reel mowers like the Tru-Cut and Trimmer were designed for St Augustine and Bermuda and various hybrids. They "stnad up" withoout folding over to be cut. Bluegrass is much softer, and will tend to roll over. The vacuum action of rotary lifts it up so the blade can cut it. That said, the easiest way to raise your McLane would be to see if you can drill another lower set of holes in the side plates to lower the front axle relative to the chassis. Also, you can weld CR bars to the wheel struts on the front axle and cross drill them to move your front wheels out another inch or so. |
Please Note: Only registered members are able to post messages to this forum. If you are a member, please log in. If you aren't yet a member, join now!
Return to the Lawn Mowers Forum
Instructions
- You must be a registered member and logged in to post messages on our forums.
- Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review the contents and make changes.
- After posting your message, you may need to refresh the forum page in order to see it.
- It is illegal to post copyrighted material without the owner's consent.
- HTML codes are allowed in the message field only.
- No advertising is allowed in any of the forums.
- If you would like to practice posting or uploading photos, please visit our Test forum.
- If you need assistance, please Contact Us and we will be happy to help.