Return to the Lawn Mowers Forum
| Post a Follow-Up
Honda OHV 160 wont start/pulls slowly
| | |
Posted by
mvron (
My Page) on
Sat, Sep 3, 11 at 9:53
Can't start this Honda mower. I don't think the engine is seized because I can rope pull or blade turn the engine. The rope pull is very hard. I was wondering about the head gasket. I drained the oil out. I think the previous owner over filled the crankcase. I got more out than I expected.
Dosen't seem to have any compression. It just turns over hard and steady - no compression. |
Follow-Up Postings:
RE: Honda OHV 160 wont start/pulls slowly
| | |
| Did you both drain the oil from the crankcase and from the cylinder? Did the oil seem like it may also have fuel in it? Is it a GCV160 OHC? |
RE: Honda OHV 160 wont start/pulls slowly
| | |
| Yes, it is a OHC. Sorry about that. I really didn't smell any fuel when draining the oil - but I didn't really check either. I'll check my old oil can and see what it smells like. I removed the spark plug - acts the same way. I removed the valve cover. Haven't checked the valves yet. |
RE: Honda OHV 160 wont start/pulls slowly
| | |
| If it pulls the same w/ the plug out, I'd go ahead and remove the 3 recoil bolts. Lift the recoil and the fuel tank off, then have a look to ensure that either the coil bolts didn't come loose and is dragging on the flywheel or that the brake isn't dragging. |
RE: Honda OHV 160 wont start/pulls slowly
| | |
| Thanks tomplun. I will do that and report back. |
RE: Honda OHV 160 wont start/pulls slowly
| | |
| I'm thinking tomplum is on the right track. My first thought was that the flywheel brake has failed to release. A little WD40 on the mechanism perhaps or replace the return spring-just thinkin' |
RE: Honda OHV 160 wont start/pulls slowly
| | |
| Sure sounds like the engine brake is dragging. |
RE: Honda OHV 160 wont start/pulls slowly
| | |
I turned the mower on end last night and poured some penetrating oil in the spark plug hole. This morning I put the spark plug in the plug hole. It was locked up tight with the penetrating oil in the cylinder. Took the spark plug out and the penetrating oil squired out of the spark plug hole when starting. Then it was back to the way it was. I took the valve cover off - the valves are working OK. I took the rope start/gas tank off to see if there was anything dragging. Couldn�t see anything. Kind of out of ideas - maybe the piston is bad - don�t know. ---------------- Thanks for the ideas. How do I get at the flywheel brake/engine brake? |
RE: Honda OHC Model 160 wont start/pulls slowly
| | |
RE: Honda OHV 160 wont start/pulls slowly
| | |
| Final result: The valve cover was dented to the point that valves wouldn't work. the other problem was that a bearing in the BBC was bad. It was replaced - ran like a champ. Some folks really abuse their lawn equipment - most folks really abuse their lawn equipment. |
RE: Honda OHV 160 wont start/pulls slowly
| | |
| Thanks for posting the result! |
RE: Honda OHV 160 wont start/pulls slowly
| | |
| Kind of a noob question but what is the BBC? because i'm thinking of the British Broadcasting Corporation. |
RE: Honda OHV 160 wont start/pulls slowly
| | |
Post a Follow-Up
Please Note: Only registered members are able to post messages to this forum. If you are a member, please log in.
If you aren't yet a member, join now!
Return to the Lawn Mowers Forum
Instructions
- You must be a registered member and logged in to post messages on our forums.
- Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review the contents and make changes.
- After posting your message, you may need to refresh the forum page in order to see it.
- It is illegal to post copyrighted material without the owner's consent.
- HTML codes are allowed in the message field only.
- No advertising is allowed in any of the forums.
- If you would like to practice posting or uploading photos, please visit our Test forum.
- If you need assistance, please Contact Us and we will be happy to help.