|
Tue, Aug 2, 11 at 3:15
| When doing a water change yesterday I noticed a strange thing when shutting off the pump. I use my settling chamber for water changes to isolate the water and treat it. As the pond level was down I had to stop the pump to refill the chamber. When I stopped the pump water started spitting out from the lid of the priming pot even though I had shut off the valve before the pump and the valve after the pump. I tightened the lid and started the pump, then shut it off again and priming pot did the same thing.Is this normal? When the pump is running no water spits out the lid and there are no air bubbles in the lid. Is it possible when the pump box flooded that some of the flooding was due to the priming pot? I have a check valve after the pump then a ball valve to control the flow to the waterfall box on that line. When the pump box got flooded all the water from the waterfall box had drained back through the line and the pump. The priming pot was full of water though. With the power going off shouldn't the check valve have kept the water from draining back through the lines and the pump? |
Follow-Up Postings:
|
| Jadal, Let me answer some of your questions backward. It depends on the check valve as to weather or not the check valve will hold back the water and what kind of shape the valve is in. If it is a swing check valve it will leak. How much depends on the valve and how it is mounted in the system. If it is a spring check valve it is less likely to leak but it will take head pressure from the pump to operate it. If it has a .5 pound spring in it you will add about 1 ft of head pressure on the pump not counting the additional friction. When the pump is off there should be no water coming out the primer pot. If you have water coming out then that indicates that the lid is either not tight or the oring seal is not good. It could be a wore out oring or something caught in the oring. It also indicates that the valve on the output or the input is leaking water through the valve. And yes that could flood the pump box depending on how fast water is leaking out the primer pot. Mike |
|
| Thanks Mike. Not sure what kind of check valve it is same kind used on sump pumps. Fixed the priming pot problem have two pumps running with a priming pot on each and had mixed up the lids. The one lid is a little smaller than the other but when switched them out no leak. |
|
| Patti, You have a swing check valve. They are all going to leak some. The good ones will only leak a drop every second to every 4 or 5 seconds. At one one drop per second the valve will let one gallon per day through the valve or not much water. The poorer quality ones will do this when new but quickly get to the point where they let more water back through them. Also a check valve in the vertical position will work better than in the horizonal position. Mike |
|
| Thanks again Mike. Both valves are vertical. You can hear them trying to stay closed or close(?) when pump is shut down. The ones on the sump pumps in the house are really noisy but the one sump pump is pumping 3600gph up six feet and out the side of the house to 40 ft from the house. I just had the one put in and I'm going to bury the pipes and make a rain garden at the end in front yard. In the winter I disconnect the pipes at outlet but sumps don't run in winter at -20F from October to April. The joys of living in Canada eh. |
Please Note: Only registered members are able to post messages to this forum. If you are a member, please log in. If you aren't yet a member, join now!
Return to the Ponds & Aquatic Plants Forum
Instructions
- You must be a registered member and logged in to post messages on our forums.
- Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review the contents and make changes.
- After posting your message, you may need to refresh the forum page in order to see it.
- It is illegal to post copyrighted material without the owner's consent.
- HTML codes are allowed in the message field only.
- No advertising is allowed in any of the forums.
- If you would like to practice posting or uploading photos, please visit our Test forum.
- If you need assistance, please Contact Us and we will be happy to help.