Return to the Tool Shed Forum | Post a Follow-Up

 o
Mongomary Ward tiller

Posted by ladybug_thumper 6 (My Page) on
Wed, Mar 1, 06 at 16:26

Hello I am new at this but I hope someone can help me out.We have a Montgomery Ward Tiller, By briggs and stratton And we do not know what year it is. The Model number is GIL 1575A and the Serial # is 26X74488 We would like to found parts and Manuel for this tiller.We have cleaned the carbon off of it and little things like that. We finially got it running but it will not stay running unless we have the choke on and the filter off. Does any one have any suggestions, or may be able to help we would really be happy to hear from you before planting garden time gets around. thank you so much hope to hear from you..


Follow-Up Postings:

 o
RE: Mongomary Ward tiller

ladybug, sounds like the main jet(in the carburator) is dirty, or partually plugged (not enough fuel....lean). jet has a very small hole in the center of it. clean the hole with a fine wire or compressed air. you might take the b&s model# and serial#, and look for a exploded view of the carb to help you out. most models are in the bottom of the float bowl. some have access from the side. hope this helps.


 o
RE: Mongomary Ward tiller

Ladybug, your Montgomery Wards tiller was manufactured by Gilson, which is now defunct. Do a Google search on Gilson tiller and you'll come up with access to quite a bit of information. I did it just as a test, and saw quite a few sites offering parts, manuals, etc. Good luck.


 o
RE: Mongomary Ward tiller

There is a site on the web ran by a guy out of Wells Maine, He is a gilson collector and has been a help to me a few times. Any search engine will have the site. Best of luck, Patrick


 o
RE: Mongomary Ward tiller

Can't do anything with the Wards numbers. However with Briggs numbers should be able to explain carb cleaning steps.

If 130000 is B&S 5hp and if 170000 is B&S 7hp or 8hp.

Will need full Model and Type number.


 o
RE: Mongomary Ward tiller

I KNOW THIS IS A LITTLE BELATED BUT MIGHT OFFER SOME HELP. I ALSO HAVE WARDS TILLER THAT IS DRIVING ME NUTS. MODEL GIL-1503 WITH B$S 5 HP MOTOR. I BOUGHT NEW IN 1973. LAST 2 YEARS DIDN'T WANT TO RUN RIGHT. WANTED TO SPUTTER OUT WHEN PUT UNDER LOAD. CARB WAS REBUILT WITH REPLACMENT PARTS FROM LOCAL MOWER SHOP. WILL NEED B$S MODEL NBRS. IT IS A VERY EASY CARB TO REBUILD. ANYWAY, IT STILL SPUTTERS. I FIGURED COULD BE BAD VALVES OR POINTS. IT STILL HAD ORIGINAL POINTS (33 YEARS OLD). YOU WILL NEED TO PULL THE FLYWHEEL TO GET TO THEM. I REPLACED THEM AT A COST 0F $7.00 AND BINGO!! THE THING STARTS AND RUNS EXCELLENT. NOW I HAVE SHEARED THE WORM DRIVE GEAR AND CAN'T FIND PARTS. MAYBE INFO ON THIS SIGHT WILL HELP


 o
RE: Mongomary Ward tiller

Gilson was absorbed by Lawnboy, so your local Lawnboy
dealer should be able to get parts if they still are
available, you might have to call Lawnboy for the part numbers.
It has been a few years, but it has worked for me.

As far as the engine, it likely has a horizontal
Briggs, which probably has the diaphragm style
carb on top of a metal gas tank.

Fish


 o
RE: Mongomary Ward tiller

THANKS FISH BOUGHT SOME PARTS ABOUT 10 YREARS AGO, BUT COULDN'T REMEMBER WHERE THEY CAME FROM
DALE


 o
RE: Mongomary Ward tiller

i now have a Mont Ward TMO 39103A Tiller without a manual. It was given to me from relative. Had been in storage. Engine would not turn over. I removed the flywheel, clean and also cleaned the pull cord spring. Found the line from gas tank totally stopped up and the carburetor in big need of cleaning, Cleaned a lot everywhere, new carb kit, air cleaner other adjustments and it starts and runs great. Need a manual to read on the gear drive mechanism to see what service is needed. Let me know if have a manual. I could email a picture of it if needed.


 o
RE: Mongomary Ward tiller

I have pdf copies of three manuals for (older) Gilson tillers that were sent to me earlier this year (I apologize for not remembering who sent them, they were very helpful).
They are for three different models, but I don't recall the specifics of each one. Two are for front tine models, one is for a rear tine model.
If anyone needs a copy, let me know and I can forward them.
Each file is about 500K in size.
Ralph


 o
RE: Mongomary Ward tiller

Ralph, Would appreciate a copy of the manuals emailed to me specifically the rear tine. grenfroe@charter.net Thanks in advance.


 o
RE: Mongomary Ward tiller

I have a Montgomery Wards GIL 39012C (SN#0098C1) that was given to me without any manuals. The tiller has a 5HP B&S motor that runs great, however I cannot get the drive belt to work correctly. Does anyone have or know where I can get a Owners Manual for this? I have tried local dealers with very little cooperation from them.

Thanks for any help.


 o
RE: Mongomary Ward tiller

  • Posted by slag lawrence, ks (My Page) on
    Mon, Mar 19, 07 at 10:36

I have a monkey ward tiller also. Engine runs great, but i think the lower end crapped the bed last night. IT makes a grinding sound and sometimes engages. I'm a pretty handy fellow, but the lower unit looks rivitted together. Are they rebuildable at all?


 o
RE: Mongomary Ward tiller

I was recently given a Montgomery Ward GIL 1594A. It has a B&S 144202.
It did not start when I first got it but I was able to successfully tear down the carb and fuel tank to get it going (it sat for 6 years with gas in the tank and the carb had never been cleaned).
Anyway, it runs and works fine now but I would like to get a copy of the manual is someone has it. Adobe PDF format would be great.
Thank you for your time.
-Brandon


 o
RE: Mongomary Ward tiller

I am looking for a Manual for a front tine Gilson tiller Model #51148. A PDF download would be greatly appreciated!

Thanks
Bill Leseberg


 o
RE: Mongomary Ward tiller

We have a Montgomery wards 5hp tiller. model GIE 39032 A SS 0344Co1 422 I would like to find a copy of a manual,or have the Belt sizes or numbers.


 o
RE: Mongomary Ward tiller

This is in response to ralphgumby's post dated Sat, Jan 13, 07 at 10:13 concerning (older) Gilson tillers and his offer to forward copies of the pdf manuals. Ralph, I would appreciate it if you would forward me copies of the two front tined tillers.


 o
RE: Mongomary Ward tiller

Hi Ralphgumby
I just sent you an email requesting a copy of manuals for front tine tillers - please reply with pdf files. Thanking you very much for your kind offer.

Bill


 o
RE: Mongomary Ward tiller

I can't figure out what the last two poster's email addresses are. I didn't receive an email from the last poster (tomewin). Post your email address in your request.
Regards,
Ralph


 o
RE: Mongomary Ward tiller

Ralphgumby

My apologies. Please email to bilmo747@hotmail.com

Thanks again

Tomewin


 o
RE: Mongomary Ward tiller

I just took-apart the transmission (worm-gear assy) on my OLD Gilson Front tine tiller. The Brass GEAR is Wiped-Out. I would appreciate ANY help finding a manual / parts list for this tiller. I can't find a Model # on it, but it's a Gilson Front Tine Tiller w/B&S 5hp motor. PDF Manuals of ANY Gilson Front Tine Tiller would be Great !!! Thanx, Andrew@Dobson.com


 o
RE: Mongomary Ward tiller

I have a 1508e? or was it 1580e anyway i have 2 of the same ones. trying to get them together i have transmission issues i need oil seals for the incomming shaft and seals for the tine shafts. Please help me I can probaly make 1 out of both of them but i need to go ahead and replace them all. I might be intrested in selling one of the transmissions. I have a bunch of motor parts from that era of briggs and stratton. my email is theskyisoutthere@netscape.net please email me any info on part numbers or where i might find them.


 o
RE: Mongomary Ward tiller

Hello Ralphgumby
I just sent you an email requesting copies of manuals for two (older) Gilson front tined tillers - please e-mail pdf files. Thank you very much for your kind offer. My e-mail address is gemret@juno.com


 o
RE: Mongomary Ward tiller

I too would like the pdf files, my email address is gwens@jjflanagan.com

Thanks


 o
RE: Mongomary Ward tiller

Not uncommon for the old horz. B & S tiller engine carb. stand pipe to get rusted or plugged at the end where the last chance filter is. I would recommend a thorough cleaning of the tank and carb. Have done this for years on my 34 year old 3 1/2 horse tiller engine. Finely had to change the points last year due to it would not fire when I drug it out to use it. I must have cleaned the carb. and gas tank 20 times I have yet to buy a gasket for it. Mine pretty simple got a belt from the engine to a chain driven tine.


 o
RE: Mongomary Ward tiller

I was given a Montgomery Ward GIL-1570B front tine tiller, last used about 1980, according to previous owner. He thinks he bought it around 1965. I have it running fairly well, with some temporary/permemnant, not quite right but good enough for now, cannibalization of parts machines my wife hates, fixes. If anyone has an owners or service manual for this tiller I would greatly appreciate a copy. Have checked with Toro and Gilson enthusiast sites with no luck. Thanks.


 o
RE: Mongomary Ward tiller

Could you send me manual for front tine my e-mail address is CatTaylor13@comcast.net I have an old GIL 1530A. Bless you Cat


 o
RE: Mongomary Ward tiller

Does someone know the model # of the 5hp B & S engine that is on a Gil 1580e tiller.
Thanks, Larry

larrymgb@sbcglobal.net


 o
RE: Mongomary Ward tiller

My manual for Gilson 1580F shows 130202-0135-07. Slightly later but should be same for 1580E.

Many different Briggs 130000 series engines will work, as long as they are 3/4" shaft to mate with the pulley, and have the large threaded boss on the crankcase cover to mount the idler arm.


 o
RE: Mongomary Ward tiller

Looking for a cover for the pulley mine needs to be replaced the model number 130292. I just need the cover plate assembly.


 o
RE: Mongomary Ward tiller

Hello Ralphgumby
I just sent you an email requesting copies of manuals for two (older) Gilson front tined tillers - please e-mail pdf files. Thank you very much for your kind offer. My e-mail address is stephen-sonia@knology.net


 o
RE: Mongomary Ward tiller GIL 39012C

Was given an old wards rototiller, model number GIL 39012C -- need to know the type (model) of the B&S 5 HP engine that went in it - all I can read is on the Ward's belt housing and it says B&S 204cc 5 HP painted on, plate on engine (if there is one) itself is completely unfindable - at least when I take the sheet metal housings off. no clue as to year etc, only that it needs an air-cleaner before I do ANY kind of work with her (gave my even older home build by Grandpa and a Mccullough chain saw engine to a far younger friend) -- thanks - gotta get summer green manure dug in, and winter green ' nuer planted -- rain took 18 inches of top soil leaving me only red clay - great if you love carrots 3 inches long, and beets 2 inch in D.!!!


 o
RE: Mongomary Ward tiller

According to my manual for Gilson 39012B, your engine is a Briggs 130292-0803-01. You can look at the Briggs website for an Illustrated Parts List. If the number doesn't work, try 130292-0803-99. Briggs often uses -99 as a catch-all.

Here is a link that might be useful: Briggs Manual Website


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Tool Shed Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here