Return to the Tool Shed Forum | Post a Follow-Up

 o
Weed Wacker Issue - Out of Ideas

Posted by mbutz13 none (My Page) on
Tue, Apr 5, 11 at 14:02

I have a weed wacker (Craftsman) that has not been working right for some time. It had bought a new carb not too long ago and then started to have more issues a few months later.

I finally decided to take it all apart, decarbonize the engine, replace the muffler, and use new seals and gaskets. After getting it back together it had the same issues. I have tried to think logically as to what is causing my problem....but I am at a loss. If anyone could give me guidance I would be extremely appreciative. Here is what is happening.

1) At first it will start with the choke on. It seems to be idling with the choke on at a higher rate than it should.

2) If I press on the gas and let go the engine dies immediately.

3) If I press the gas further and hold, it will increase in speed but then after about 5-10 seconds start to get weaker and then die.

4) If I repeat this process a few times it will not start with the choke on. The only way to get it to start at that point is without the choke on.

5) Eventually it doesn't matter if the choke is on or off...it won't start.

Thank you in advance for any help or suggestions.


Follow-Up Postings:

 o
RE: Weed Wacker Issue - Out of Ideas

Are you getting spark after it dies? IF not it maybe the kill switch or ignition parts that are bad or intermittent? I would also check the kill switch make sure it's good?

Does it hit off carb. cleaner when it won't start (by spraying 2 second blast directly down the carb. venturi or removing the spark plug and spraying 1 second bast directly into the comb. chamber. IF so, when you get it to run and pull the throttle can you see gas itomizting from the fuel manifold that has the mid and high speed gas port?

Last thought would be if it's getting spark when it dies and it will run off carb. cleaner till it runs out of cleaner you sparyed in. I would say you've either got vacuum leak (internal in the carb., at the intake manifold or at the jug where it held on at the crank case (usually 3 or 4 screws) or carb. diagram installed backwards especially on the needle and set side or internal passage plugged in the carb. or through the carb base to the crankcase.

IF this didn't spark some ideas then I would got to Zamacarb.com or walbro.com and study the troubleshoot trees see if that may help?


 o
RE: Weed Wacker Issue - Out of Ideas

  • Posted by baymee LehighValleyPA (My Page) on
    Wed, Apr 6, 11 at 5:43

Does the muffler have a spark arrester screen and is it clean? Is there carbon in the exhaust port?


 o
RE: Weed Wacker Issue - Out of Ideas

I will be sure to try both of those things and get back to you with the results. As far as the muffler I replaced it because I also thought that could be the issue.


 o
RE: Weed Wacker Issue - Out of Ideas

check your fuel line for cracks. Also make sure your carb is adjusted correctly. Also make sure you don't have any leaks around the seals you replaced. Sounds like you have a lean condition.


 o
RE: Weed Wacker Issue - Out of Ideas

Is there a special tool required for adjusting the carb (lean/rich)? Its a craftsman weedwacker. What is the best way to ensure the carb is adjusted correctly?


 o
RE: Weed Wacker Issue - Out of Ideas

rcmoser - Here some answers to your questions:

1) Yes I am getting spark after it dies because if I wait just a bit I can get it to start again.

2) I began by using the choke each time after it dies until that no longer worked. Then I disengage the choke and it would start. I would do this until that no longer worked. Then I sprayed in carb cleaner. It did hit off the carb cleaner for a short period but I saw no itomizing anywhere.

I do see air in the lines. Perhaps there is a crack somewhere. I think I'll start by replacing those first.

What sort of tool is used to adjust the carb? It does not seem to be any typical head. It actually looks like it will require a female end to turn it.


 o
RE: Weed Wacker Issue - Out of Ideas

Probably need spline wrench. You could use needle nose pliers. Some get the hi/lo screws out and cut screwdriver slot so you can use screwdriver to adjust. I would mark them first to see if you can acutally move them and for reference where you started.

Does this model have primer button? if so it maybe cracked. If you fuel lines or primer button have cracks it will cause fuel not to be pulled up to the carb. I would suggest you just replace the fuel lines and clean or replace the filter that at the bottom of the tank connected to the fuel line. It will take awhile to get the air out of them and fuel to start pulling up and through the carb. so you may have to prime with carb. cleaner several times.


 o
RE: Weed Wacker Issue - Out of Ideas

I replaced the tubes and didn't see a change so I decided to pull the high and low screws out (with tiny pliers). In the past I was unable to move them back and forth very easily because it requires a special tool. Once I pulled them I cut a groove in each one and "presto" I could adjust them with a screw driver. After a little adjustment here and there it seems to been running pretty well.


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Tool Shed Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here