Return to the Tool Shed Forum | Post a Follow-Up

 o
echo srm 200 da points gap

Posted by the_0utsider (My Page) on
Tue, Sep 10, 13 at 0:06

Anyone have a book what the points gap should be?
While it is virtually the same motor as my old stihl fs80, i dont feel like taking it apart to find out.

Also, being the ignition coil is inside the flywheel, how do i adjust that gap?

TIA.


Follow-Up Postings:

 o
RE: echo srm 200 da points gap

Point gap is .020.

Coil to flywheel gap is using special cut-away flywheel. Sold by Echo/Kioritz as a service part. Not sure if still available, Echo converted electronic ignition and external flywheel about 30 years ago.

This post was edited by ggoyeneche on Wed, Sep 11, 13 at 8:01


 o
RE: echo srm 200 da points gap

Please post a picture of your motor with the flywheel off showing the points and coil.

1. I would like to see that the coil’s gap is adjustable vs fixed under the flywheel.

2. If it is adjustable, I can understand a cut-away F/W is a convenient time saver but I feel there is a trial and error method. Such as: letting the magnet pull a “marked positioned” lightly tightened coil to it with the .010 index or business cord fixed to the magnet or coil. Turn the fly/w away from your coil. Hopefully the marks coil's position will show you the coil did move (if needed) and now tightened it more. Slightly tighten the fly/w and check for fire. Turning by hand with the plug out. If you have good fire, add final torque to coil and fly/w.

3. IMO you can get the coil less than .010 as long as there is no contact w/o problems.

Old School 101. LOL!


 o
RE: echo srm 200 da points gap

If coil located under flywheel, following steps should be taken to adjust magneto air gap:
1)Remove flywheel.
2)Place piece of electrical tape on inside rim.
3)Replace flywheel (finger tight).
4)Rotate it 10 to 12 times (removing spark plug will make engine easier to rotate by hand).
5)Remove flywheel and examine tape.
6)If tape scuffed, air gap clearance too small.
7)If tape isn’t scuffed, add another strip, repeat test. If tape still not scuffed, air gap clearance too great.
8)Adjust position of armature, until air gap clearance such that one layer tape isn’t scuffed but two layers are when flywheel rotated.

I found this method at the address below along with other good small engine info.

http://smallengineinformation.com/?page_id=421


 o
RE: echo srm 200 da points gap

I havent got around to look further but here is a pic of the points.
When i put the flywheel on, it sounds like it is rubbing. ill do more troubleshooting when i have the chance.

Thanks!


 o
RE: echo srm 200 da points gap

My old trimmer repair manual says that the Echo point gap is .014-.016 inches. I have a very old Echo SRM-140DA but converted it to electronic ignition.


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Tool Shed Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here