Return to the Tool Shed Forum | Post a Follow-Up

 o
ID parts of old floor jack

Posted by lilydude sunset6/z8 (My Page) on
Sun, Nov 16, 08 at 13:04

This is a view of my old Strongarm floor jack. Does anyone know what the two threaded covers are? I removed cover #2, and there was a threaded screw under it, maybe an adjustment screw, but I'm not sure. I would like to replace the hydraulic fluid in this unit. Any info would be appreciated.

Photobucket


Follow-Up Postings:

 o
RE: ID parts of old floor jack

  • Posted by canguy British Columbia (My Page) on
    Sun, Nov 16, 08 at 13:09

#2 will be the relief valve adjustment, leave it alone unless you are having problems with it.Normally, you should not need to change the oil unless it is contaminated.


 o
RE: ID parts of old floor jack

I read on another thread that you should change the hydraulic fluid every couple of years. Any opinions on that? In any case, can someone tell me what cover #1 is for?


 o
RE: ID parts of old floor jack

I'm not specifcally familiar with Strongarm, other than it was an inexpensive imported jack. Parts may be difficult if not impossible to obtain.

That said, both threaded plugs are probably relief valves. One is set to crack when the main ram attempts to lift more than the capacity of the jack. The second cracks and bypasses presure if you continue pumping after the jack is fully raised. This is to prevent blowing out seals. Can't say this is how Strongarm did it, but this is how Hein-Werner, Walker, and Weaver used to design their floor jacks.

As for changing the fluid, no real reason, and not recommended by manufacturers, unless you have reason to believe fluid is contaminated Jack oil is different than brake fluid and isn't contaminated the same way brakes are with moisture.

If you still want to change the fluid, find the filler plug (usually on top of the main ram) and remove, invert the jack and drain, and then refill with jack oil. Do not use brake fluid. Brake fluid will destroy the seals.


 o
RE: ID parts of old floor jack

Thanks, ggoyeneche. That solves the puzzle.

Are you sure it was an inexpensive import? The jack is about 40 years old. It's rated at 1.5 tons, but it looks like it could lift a dump truck. And it's still working.


 o
RE: ID parts of old floor jack

canadian

Here is a link that might be useful: jack company


 o
RE: ID parts of old floor jack

Google "Strongarm" and you'll see. There used to be five quality US manufacturers, the three I mentioned, plus Blackhawk and Milwaukee. Only Milwaukee still builds in the US. Everything else was offshore, first from Japan, then Taiwan and Denmark, then China.


 o
RE: ID parts of old floor jack

I Have a Napa Fleet Floor Jack Mod.# 91-632
Ser.#6 632 J0633 1 1/2 tons Made By DE Koven MFG. Co. Racine Wis. Some one that works for me took the pumper all apart and has lost some of the parts I would like a parts break down or a diagram
at the present time all it does is when you pump it it just pullsates up and down with the handle action it seams that it is not keeping the presure in I do not know what is wrong I am just asumeing that they lost some parts or it may be that all the parts are there but that one of them is worn out I need some thing to go by


 o
RE: ID parts of old floor jack

That looks a lot like my very old Hein-Warner, an American made great jack that parts are still available for. If it is not leaking and will still raise up all the way there's nothing for you to worry about. Use and enjoy it, they're great jacks.


 o
RE: ID parts of old floor jack

can you tell me the number or size of the seal that is around the pump piston on sears model 214.124500 11/2 ton, or is their a manual somewhere? I hate to throw the jack away because of a seal, the jack was never used.


 o
RE: ID parts of old floor jack

Way back, when my 55 year old son was messing with hot-rods, we bought him and me 2 floor jacks from Sears. He was about 14. Both jacks are still working. They sit in cold garages all year around, have never failed to work, and never get cleaned off.
Those junk jacks from China, etc, are not worth the powder to blow them up!


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Tool Shed Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here