Return to the Tool Shed Forum | Post a Follow-Up

Stihl MS 290 No Spark

Posted by etbrown4 none (My Page) on
Sun, Dec 11, 11 at 14:40

I see no spark on the plug when I ground it against the carb, and pull the rope.

I've tried 2 plugs.

I have the choke in the 'full choke' position.

I have the chain brake 'on' or thrown forward.

Shouldn't you be able to see a spark when pulling the rope?

What is the next step?

Any tips are appreciated.

Follow-Up Postings:

RE: Stihl MS 290 No Spark

Some say that you can't ground a plug against the carb on this model Stihl.

If so, how to you test the plug while watching for a spark?

RE: Stihl MS 290 No Spark

I have found that sure enough, I do have spark.

To see it, I have to take a piece of copper wire, wrap it around the base of the plug and let the other end contact the head. Bingo, plenty of spark, though it's yellow.

Now, the plot thickens. With 'ether' shot into the cylinder or through the carb, I am getting firing in the cylinder.

I've worked on lots of different motors including thousands of hours flying and working on 2 cycle ultralight airplane motors.

For now, I'm stumped. How can you have fuel and spark and no fire?

Is this unique to a Stihl, because I can't recall seeing this before and that covers 50 years of twisting wrenches!

RE: Stihl MS 290 No Spark

If it fires on ether (which I'm not sure I would be doing in a 2 stroke) then I would look at the carb. I might also pull the muffler and see if there is any scoring on the piston (low compression). Did the saw set for along while with bad gas in it? If so then again I would say carb. Always replace the in tank fuel filter when you do the carb, I've heard it too can become clogged with varnished fuel. Check the fuel line in the tank, if it's old enough it can colapse causing fuel starviation. I would also give it the poor man's compression check. Lift the saw by the start handle. If the engine makes enough compression it will usually lift the saw off the ground. If you have low compression it will not lift the saw off the ground. Check out You Tube for vids.

RE: Stihl MS 290 No Spark

  • Posted by zenman Ottawa KS 5b (My Page) on
    Sat, Dec 17, 11 at 0:24

The maintenance chart on my MS 361 says to replace the pickup body (the in-tank fuel filter) every 12 months. I did that about a month ago for the first time, even though I have had my saw for several years. The old one that I removed looked pretty clean to me, but I suppose there could be something clogging it that wasn't obvious to the eye. I agree with c3pilot that using ether is questionable in a 2 stroke.

RE: Stihl MS 290 No Spark

Ether will not harm a 2-stroke engine using common sence !
Carb cleaner is a better usage since it will clean and supple a useable flash Point for combustion :)

 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!

Return to the Tool Shed Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.

Learn more about in-text links on this page here