Return to the Tractors Forum | Post a Follow-Up

 o
John Deere L100 won't crank

Posted by mamick122 none (My Page) on
Sun, Jul 27, 14 at 19:43

I have a 10 year JD L100 with the 17.5hp B&S motor. Yesterday I shut it off and now I cannot get it to crank. Here is what I have tested:

- Tested all three safety switches (seat, PTO, and brake) all function correctly according to ohm meter.
- If I jump 12 volts to solenoid (Disconnect hot wire form ignition) it cranks, but does not start with key on.
- I then disconnected connector from back of ignition switch and put a jumper between Battery "B" and Magneto "M" and put 12 volts directly to solenoid, again cranked but would not start.
- With the ignition switch disconnected I tried to jump Battery "B" to starter/Solenoid "S" on the connector and it does not attempt to crank.
- Also the lights do not come on when the key is in the light position, if I jump 12 volts to the lights directly they work
- I connected the ignition connector back to the ignition switch and measured the voltage between the lights "L" and ground and it shows less than one volt when the switch is set to the Lights position.

I don't think it is the ignition switch since when I tried to jump around it through the connector it didn't work either.

At this point I am guessing a short somewhere. I am at a loss trying to find the short, is there anything I am missing?


Follow-Up Postings:

 o
RE: John Deere L100 won't crank

Well, when you connect B to M, you probably fried the magnetron.
That wire is GROUNDED to KILL spark. Otherwise, it works just like the coil on your batteryless walk behind mower.

Did you think to check the fuse?


 o
RE: John Deere L100 won't crank

Yes, checked the fuse, I even measured with ohm meter to make sure. I also tried connecting B to L directly and the lights won't come on. But if I connect the battery directly to the lights they do come on.


 o
RE: John Deere L100 won't crank

Do you have 12V at B on the plug?


 o
RE: John Deere L100 won't crank

Was traveling for work just got back and checked yes, there is 12V on B.

This post was edited by mamick122 on Thu, Jul 31, 14 at 22:58


 o
RE: John Deere L100 won't crank

You hav 12V at B.
You connect B to L and have no lights?
Doesn't make sense.


 o
RE: John Deere L100 won't crank

OK- Looking at the schematic-
The L terminal is connected to the B terminal at the Voltage Regulator. RED & PURPLE.
At the harness connector-
RED becomes RED/BLACK
PURPLE becomes YELLOW/WHITE.

The actual "feed to the lights is A2.
Kind of backwards from "typical" schematics.
So, if you connect either B or L to A2, you should have lights.

For the crank circuit-
Key switch S terminal (purple) goes to the PTO switch.
PTO switch to Brake switch (purple/white) to solenoid terminal (purple)

This post was edited by bill_kapaun on Fri, Aug 1, 14 at 11:35


 o
RE: John Deere L100 won't crank

Thanks everyone for your help, I figured it out. As I looked at the battery voltage I noticed at the battery it was 12 volts but at the harness to the switch it was 11.9. So I started walking back from the battery to the harness tying to jump over to the solenoid.

When I tried to to crank from the hot side of the fuse it would not crank. I popped open the connector on the small hot wire between the fuse and the solenoid and it had corrosion in there. I cleaned it out, sprayed a little DW40 on it, snapped it back together and now it cranks right up!

Still no lights but those haven't worked in a while, maybe corrosion somewhere else. But at least now I can mow!


 o
RE: John Deere L100 won't crank

gotta ask - has someone been using either a power washer or garden hose to wash the machine down? if so, that may by the source of the corrosion you found... allus best to use compressed air or leaf blower to get trash/clippings off machine after each use; L&G powered eqpt isn't designed/built to withstand getting wet a lot..particularly the electrical systems.


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Tractors Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here