Return to the Tractors Forum | Post a Follow-Up

Worth replacing head gaskets?

Posted by arhick (My Page) on
Wed, Oct 30, 13 at 0:20

My brother asked me about doing his head gaskets in his riding mower with a Kohler Cv730 engine and I'm unsure if I am up to task on this. A local shop wanted $400 to do the repair. Are these Kohlers worth the repair and do they normally go well?

Follow-Up Postings:

RE: Worth replacing head gaskets?

Best way for you to determine the correct answer to that question (the "unsure of capability" part) is to go to the Kohler website and download a free PDF copy of the service manual for that engine family.
The Kohler manuals are good and when you study the procedure in the manual you will be better able to decide if it's you or not.
One thing you want to be sure to do if you try it is to shoot plenty of pictures of everything before you remove the first part and after that, shoot pictures at every step or part removed.
How many times have folks gotten themselves into a bind because they didn't record the disassembly process?
You might even check the videos on yoo toob to see if there is something on the exact engine. But do get the Kohler manual first and start studying.
There are other members here who make their bread money working on Kohlers and will probably offer encouragement too.

RE: Worth replacing head gaskets?

Yes, review the manuals. It will take a 3-4 hours of your time if you are mechanically experienced -of course depending on the application. Some just take longer. If you have good dexterity and a set of gear wrenches, you can cut down the time and keep exhaust pipes on many times. That is if the heads on your engine are retained by bolts rather than studs.

RE: Worth replacing head gaskets?

Thank you for the suggestion, gents. I will get the gaskets ordered. Please stand by!

RE: Worth replacing head gaskets?

Time to figure out your cleaning supplies. Clean up is the most tedious part as you need to not gouge the aluminum. My favorite is the course, kind of plastic looking scuffing pads. A gentle removal w/ a razor blade to get the bulk of the gasket away first, then use your scuff pad or scotch brite. When all the debris is gone, wipe down with some spray carb clean or mineral spirits on o towel. Remember to lower the piston slightly to get at any bits out that found their way in there. You also want to clean the chamber of the hard deposits and refresh the spark plugs too. Plug the push rod galley with a clean towel and put the piston at the top to help keep contaminants out. have fun!

RE: Worth replacing head gaskets?

I wanted to report back that the repair is done. In watching a Youtube video, I saw where they scraped the head gasket off w/ a puddy knife and didn't do further clean up. I went further as you suggested and it was amazing how much more gasket material came off. Thank you, thank you. I'm much more confident that the repair will last. I would go poor doing these for a living as it took over 5 hours. I felt that I had to remove the exhaust pipes even with it having bolts that held the head down. The gasket blew out in between a small hole that went through the head and the large cylinder hole. I see that the gasket is mad differently now so I would hope it is meant to last. I winged it on one part where the instructions said to install the gasket with the numbers up. I assumed that it meant towards the head and that maybe the instructions were meant for the side shaft models that the heads are on top. Did I do good? Thanks again everyone for your support.

RE: Worth replacing head gaskets?

5 hours is "student time", you are a student.
The word "UP" defines as "toward cylinder head" in this case.
Your score is nearly 100%.
Good results.

RE: Worth replacing head gaskets?

5 hours is much faster than 4 hours twice.
Being slow & methodical for a "learning experience" is usually a much shorter path to a successful outcome.

I build bicycle wheels. When I take a methodical approach, I end up with a GOOD, evenly tensioned wheel much faster.

 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!

Return to the Tractors Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.

Learn more about in-text links on this page here