Return to the Irrigation Forum | Post a Follow-Up

 o
Converting Rainbird Sprinklers to Garden Irrigation?

Posted by Dulahey 7a (My Page) on
Mon, Jan 28, 13 at 12:48

My wife and I recently purchased a house and I am busy on getting our raised vegetable garden beds built and ready to go for this spring.

The previous owners had a sprinkler system installed that covered the entire property. However, I do not want to use sprinklers on my vegetable garden. My original idea was to build my own irrigation system out of PVC pipe, but since there are sprinklers everywhere, I figure I can just convert one of the zones into a drip/emitter irrigation system.

The zone in question is a straight line of 14 different model 1800 sprayers against my north fence. They are spaced about 10 feet apart. I plan on building 16'x4' raised beds and so each bed could be watered by two of the current 1800 sprayers.

I've done a little bit of research and it seems I can buy a converter that goes into the existing sprayer that just creates a 1/4" male plug that you can then attack tubing to. Then place emitters on the tubing.

Does anyone have any experience/tips/suggestions about this process? Am I heading down a road of frustration? I have no experience with Rainbird products. Does the tubing not last very long? I assume it's best to keep the tubing covered with mulch to make it last longer? Are the emitters terrible?

If I do it this way each existing sprayer head will be converted to water a 8'x4' densely planted area. I'm assuming it could handle this?

Any advice is greatly welcomed. Thanks!

This post was edited by Dulahey on Mon, Jan 28, 13 at 12:50


Follow-Up Postings:

 o
RE: Converting Rainbird Sprinklers to Garden Irrigation?

Dul,

You can make you system more flexible by digging down and removing the heads at the lateral line and replace them with a valved riser and then use your drip system. Then each section can be irrigated separately. You will need to do this when gardening with different planting of varying different watering patterns and different harvest and planting time. Just a suggestion. Aloha


 o
RE: Converting Rainbird Sprinklers to Garden Irrigation?

So the lateral lines are most likely just PVC pipe?

And then to water my beds I would just turn on that zone and manually choose (with a ball valve?) which bed I want to water?

This sounds like a good idea, but I would be unsure about pressure and what not. Pressure isn't really regulated in a lawn sprinkler system is it? Would it be best to put some kind of regulater on each bed?

Thanks for the response btw!


 o
RE: Converting Rainbird Sprinklers to Garden Irrigation?

Dul,

Pressure is the dependent on how many outlets or sprinklers are in operation. If you have only one riser running then it will receive all the system pressure. The flow rate will be dependent on the cross-sectional area of the pipe and pressure. Systems are designed to handle the way the irrigation is set up knowing the flow rates of all the system irrigation heads and the overall system pressure. You could calculate what you can do by knowing each component's flow rate and pressure drop. But most people do things by trial and error. Which way do you want to go. To calculate the design, you need to some homework. For starters, the system's total flow rate and pressure. Would you know how to find those? Aloha


 o
RE: Converting Rainbird Sprinklers to Garden Irrigation?

I would not. I don't have any data on pressure or flow. I'm pretty sure trial and error would be how I would go.

This is kind of why I was originally leaning towards using the Rainbird converters because they contain a pressure regulator in them. I figured this would take care of any issues. Although, this is the most expensive way too.


 o
RE: Converting Rainbird Sprinklers to Garden Irrigation?

Dul,

You will not be sure what flow rate you will receive from the emitters because of the pressure regulation but it doesn't really matter. Just adjust the time of irrigation to apply the amount you believe the plants need according to their life cycle. There is a way to measure the flow rate from the emitters if you are interested.

Are you using municipal water from a outside faucet for your system or from your yard mainline before it enters the house? aloha


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Irrigation Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here